- Raymarine St60 Wind Service Manual User
- Raymarine St60 Wind Vane
- Raymarine St60 Wind
- St60 Wind Manual
- Raymarine St60 Tridata Manual
There must be a magnet in the vane. You can adjust the display head by following instructions in the manual. IIRC, you press and hold CAL for 3 seconds then use the arrow keys to adjust the needle, once you’ve lined the vessel up into the wind. Capteurs Wind, ST50 Wind or ST60 Wind). Power the Raymarine manual for the sensor's alignment. Simpson Lawrence manual windlass. Stainless steel sampson post New AC-Delco 8DA deep cycle service battery (2014) 420 aH. New group 31 starting Radar – Autohelm ST50 plus, with mast mounted Radome VHF – Uniden Oceanus. View online Owner's handbook manual for Raymarine ST60 Tridata Marine Equipment or simply click Download button to examine the Raymarine ST60 Tridata guidelines offline on your desktop or laptop computer. ST60 Wind and Close Hauled Wind Instrument Owner’s Handbook EMC conformance All Raymarine equipment and accessories are designed to the best industry standards for use in the leisure marine environment.
Raymarine St60 Wind Service Manual User
Thread Rating:- 0 Vote(s) - 0 Average
St60+ no wind speed or directional display |
Post: #1 |
| St60+ no wind speed or directional display Hi I have a st60+ wind with a masthead transducer and I have no speed data or direction. Dials do move in boat show mode. Voltages at display are Red to shield 8.02 Blue to shield 7.31 Green 7.31 Yellow 8.04. There is power to the display, I have three dashes in the speed area. I can not calibrate or place the display in master mode. It is stuck in repeater. I have done factory reset a number of times. I thought there was a hard reset that could be done but I forgot the key sequence. Any help would be appreciated. Thanks, Mark |
01-23-17, 04:50 PM (This post was last modified: 01-24-17 09:05 AM by Chuck - Raymarine - Moderator.) |
| RE: St60+ no wind speed or directional display Mark, See my comments below regarding the transducer test measurements which you have performed: - Red to shield 8.02 ... normal - Blue to shield 7.31 ... high indicative of no ground reference - Green 7.31 ... high indicative of no ground reference - Yellow 8.04 ... high indicative of no ground reference Should the wind transducer's ground lead (black/bare lead) be connected to the wind transducer ground terminal (grey) and the problem persists, then it may indicate a problem with the wind instrument not providing a ground reference via its wind transducer ground terminal. Such failures may sometimes be worked around simply creating a jumper lead and then using it to create a jumper between the SeaTalk ground terminal of the wind instrument and the wind transducer's ground lead. Please note that Raymarine can no longer service ST60/ST60+ instruments. Should the instrument need to be replaced, then it may be replaced with a i60 Wind Instrument. |
Post: #3 |
| RE: St60+ no wind speed or directional display Hi Chuck, Thanks for the help and sorry if this is duplicate, I'm having trouble navigating this forum. Where is the ground terminal on the wind transducer. Is it a screw on the installation pad/puck. Are there wiring connectors under the puck or is the wire hard wired to the puck/pad. Following your train of thought there could be a bad/corroded connection on the screw in portion of the transducer as well. Let me know your thoughts. Thanks, Mark |
01-24-17, 10:08 AM (This post was last modified: 01-24-17 10:10 AM by Chuck - Raymarine - Moderator.) |
| RE: St60+ no wind speed or directional display Mark, While less likely, it is indeed possible for corrosion of the masthead transducer's pins or mounting block may be responsible for preventing a ground reference. Please click here to view a FAQ addressing the pinout for the masthead transducer and mounting block. Please click here to view a FAQ addressing the pinout for a SeaTalk socket. The wind instrument transducer display's transducer ground terminal features gray marking. |
Raymarine St60 Wind Vane
Post: #5 |
| RE: St60+ no wind speed or directional display Hi Chuck and thanks for the information. To confirm you suggest trying a jumper wire on the instrument from sea talk ground to transducer ground. Is that correct? Thanks for confirming and I understand no guarantees, Mark |
Post: #6 |
| RE: St60+ no wind speed or directional display Mark, Q) To confirm you suggest trying a jumper wire on the instrument from sea talk ground to transducer ground. Is that correct? A) Yes. |
01-25-17, 12:20 PM (This post was last modified: 01-25-17 01:11 PM by Chuck - Raymarine - Moderator.) |
| RE: St60+ no wind speed or directional display Hi Chuck, I made the jumper, installed, and tested with no improvement. |
Post: #8 |
| RE: St60+ no wind speed or directional display Mark, Unfortunately, as the jumper did not resolve the problem, then the fault may be rooted in the wind instrument or the transducer. As Raymarine can no longer service ST60+ instruments, you may want to consider sending the wind transducer to Raymarine’s Product Repair Center to be bench checked / serviced. Should the transducer be found to be operational, then the ST60+ Wind may be replaced with an i60 Wind or with the combination of an i70 MFID and iTC-5 Analog Instrument Transducer Converter. |
« Next Oldest | Next Newest » |
Raymarine St60 Wind
User(s) browsing this thread: St60 Wind Manual
Raymarine St60 Tridata Manual
Contact Us | Raymarine forum | Return to Top | Return to Content | Lite (Archive) Mode | RSS Syndication